Welcome to the official website of Nanda Automation Technology Jiangsu Co.,Ltd

CN  丨  EN

这是描述信息
这是描述信息
南大傲拓科技江苏股份有限公司

Product

All categories
搜索
Search
  • NAProSetupV606.rar

  • NAProSetupV580.rar

  • NA400PLCUserManual(V27).rar

  • NA400PLC.rar

NA400-Profibus DP slave module
0.0 0.0

Serial port module type

CMM401-0103

Order number

400CMM4010103

Power consumption

2.0W/5V

Current consumption

400mA/5V

Number of bus interfaces

1

Bus interface type

Profibus DP slave

Support communication baud rate

4800~12Mbps

Interface isolation

Photoelectric isolation 2500V rms

Programming Drive

Manufacturers provide GSD files

Weight

220g

Dimensions (W×H×D)

40mm×145mm×158mm

*The information provided in this article is just a general description and feature introduction of the product. The content in this article may change with the further development of the product, and the right of interpretation belongs to Nanda Automation Technology Co., Ltd.

Product description
Parameters
Performance parameters
Download

Profibus DP slave module

CMM401-0103

 


 

Features

Standard PROFIBUS-DP slave interface: DP-V0/V1 protocol, in line with IEC61158 and Chinese national standard GB/T20540-2006: Fieldbus for measurement and control of digital data communication industrial control system Part 3

The baud rate can be set, the maximum baud rate is 12M.

Up to 30 slave stations can be connected on the Profibus bus.

Maximum expansion I/O module: 32-point DI/32-point DO module ≤32 blocks; 16-point AI module ≤7 blocks; 4-point AO module ≤7 blocks.

Intelligent module, powerful self-diagnosis function, the module can automatically reset and restart the unique data safety output function when the module fails, so that the control device has a higher safety function.

Comprehensive LED indicators: comprehensive LED indications of power supply, module activation, module operation, fault, PROFIBUS bus operation and fault.

Support hot swap.

 

 


 

Module hardware settings and external interfaces

1. DP slave address coding switch

The module provides two decimal rotary coding switches S1 and S2, DP slave address = S1*1+S2*10, which needs to be set correctly before power on.

模块

 

2. Two-digit DIP switches K1 and K2

模块

K1: The system is reserved for updating firmware. Before the module is powered on, please confirm that K1 is in the OFF position.

K2: Optional switch for the 120-ohm terminal resistance of the bus cable. The OFF position indicates that the terminal resistance is not connected, and the ON position indicates that the terminal resistance is connected.

 

3. DP communication interface

DP-S: Standard SUBDB9 Female interface, the interface lead definition is shown in the following table:

NO.

Pin definition

NO.

Pin definition

NO.

Pin definition

1

SHIELD optional

4

CNTR_P

7

P24

2

M24 optional

5

DGND

8

RS485_N

3

RS485_P

6

P5V

9

NC

  Note: The NC table is not connected.

 

Due to physical and electrical performance limitations, the maximum number of modules that can be connected to the Profibus bus is 30. Please pay attention to this limitation when configuring. If the number of slave stations must be greater than 30, please add profibus relay equipment.

 

*The information provided in this article is just a general description and feature introduction of the product. The content in this article may change with the further development of the product, and the right of interpretation belongs to Nanda Automation Technology Co., Ltd.

Scan the QR code to read on your phone
We could not find any corresponding parameters, please add them to the properties table

Serial port module type

CMM401-0103

Order number

400CMM4010103

Power consumption

2.0W/5V

Current consumption

400mA/5V

Number of bus interfaces

1

Bus interface type

Profibus DP slave

Support communication baud rate

4800~12Mbps

Interface isolation

Photoelectric isolation 2500V rms

Programming Drive

Manufacturers provide GSD files

Weight

220g

Dimensions (W×H×D)

40mm×145mm×158mm

*The information provided in this article is just a general description and feature introduction of the product. The content in this article may change with the further development of the product, and the right of interpretation belongs to Nanda Automation Technology Co., Ltd.

底部二维码

Time of issue:2020-06-24 00:00:00

Welcome  to  Nanda

Automation  official  Wechat

底部联系方式

Time of issue:2020-06-24 00:00:00

Address: 199 Qingshui Ting West Road, Jiangning Economic Development Zone, Nanjing

Telephone: 025-68530188 (Switchboard)

Fax: 025-68530178

Service Hotline: 400-025-0150

Technical support: 025-68530179

底部备案号

Time of issue:2020-06-22 00:00:00

Nanda Automation Technology Jiangsu Co., Ltd.     Record number: 苏ICP备090423423号-1